SLIO > Signal modules digital
022-1SD00 - Signal modules digital | Digital output modules
Order no. |
022-1SD00 |
| Type | SM 022 |
| Module ID | 0C81 1E00 |
General information |
|
| Note | - |
| Features | 4 outputs Safety Output current 0.5 A |
Current consumption/power loss |
|
| Current consumption from backplane bus | 75 mA |
| Power loss | 1 W |
Technical data digital outputs |
|
| Number of outputs | 4 |
| Cable length, shielded | 1000 m |
| Cable length, unshielded | 600 m |
| Rated load voltage | DC 20.4...28.8 V |
| Current consumption from load voltage L+ (without load) | 15 mA |
| Total current per group, horizontal configuration, 40°C | 2 A |
| Total current per group, horizontal configuration, 60°C | - |
| Total current per group, vertical configuration | - |
| Output current at signal "1", rated value | 0.5 A |
| Output delay of "0" to "1" | 100 µs |
| Output delay of "1" to "0" | 175 µs |
| Minimum load current | - |
| Lamp load | 5 W |
| Parallel switching of outputs for redundant control of a load | not possible |
| Parallel switching of outputs for increased power | not possible |
| Actuation of digital input |  |
| Switching frequency with resistive load | max. 50 Hz |
| Switching frequency with inductive load | max. 0.5 Hz |
| Switching frequency on lamp load | max. 10 Hz |
| Internal limitation of inductive shut-off voltage | L+ (-45 V) |
| Short-circuit protection of output | yes, electronic |
| Trigger level | 1.7 A |
| Number of operating cycle of relay outputs | - |
| Switching capacity of contacts | - |
| Output data size | 4 Bit |
Status information, alarms, diagnostics |
|
| Status display | green LED per channel |
| Interrupts | yes, parameterizable |
| Process alarm | no |
| Diagnostic interrupt | yes, parameterizable |
| Diagnostic functions | yes, parameterizable |
| Diagnostics information read-out | possible |
| Supply voltage display | green LED |
| Group error display | red SF LED |
| Channel error display | red ERR-LED and yellow ER2-LED |
Isolation |
|
| Between channels | - |
| Between channels of groups to | - |
| Between channels and backplane bus | |
| Insulation tested with | DC 500 V |
PWM data |
|
| PWM channels | - |
| PWM time basis | - |
| Period length | - |
| Minimum pulse width | - |
| Type of output | - |
Safety |
|
| Safety protocol | PROFIsafe V2 |
| Safety requirements | SIL CL 3, PL e, Kat 4 |
| Secure user address | 1 - 4095 |
| Watchdog | parameterizable 10ms - 1s |
| Two channels | Each 2 of 4 outputs switchable |
| Test pulse length | parameterizable 500µs - 10ms |
| Circuit monitoring | |
Datasizes |
|
| Input bytes | 5 |
| Output bytes | 5 |
| Parameter bytes | 44 |
| Diagnostic bytes | 20 |
Housing |
|
| Material | PC / PPE GF10 |
| Mounting | Profile rail 35 mm |
Mechanical data |
|
| Dimensions (WxHxD) | 12.9 mm x 109 mm x 76.5 mm |
| Weight | 60 g |
Environmental conditions |
|
| Operating temperature | 0 °C to 60 °C |
| Storage temperature | -25 °C to 70 °C |
Certifications |
|
| UL certification | yes |
| KC certification | yes |
[Datasheet]
